SOFTING | ATEVA Technologies

SmartLink HW PN

Webmaster — Wed, 10 Sep 2025 10:50:36 +0000

SmartLink HW PN

PROFINET Gateway for Asset Management

Access PROFINET networks via FDI and OPC UA

smartLink HW-PN provides access to PROFINET networks. By integrating standardized technologies like a FDI communication server (OPC UA), it provides transparent access to all connected devices.

smartLink HW-PN can be used for asset management, device configuration and monitoring.

Asset Management and Parameterization of PROFINET Devices

Parameterization and Asset Management

Secure, standardized access to devices
Parallel to and independent of the controller

Compatible with established communication standards

Implements the standard FDI communication server interface based on OPC UA

Asset Management and Parameterization of PROFIBUS Devices

Parameterization and Asset Management

Secure, standardized access to devices
Parallel to and independent of the controller

Inexpensive and low-risk Integration

Connection of PROFIBUS devices without additional hardware
Use of existing infrastructure using the PROFINET/PROFIBUS proxy standard for connecting to the PROFIBUS devices

Compatible with established communication standards

Implements the standard FDI communication server interface based on OPC UA

Parameterization and Asset Management

Independent of PROFINET engineering tools
Centralized and time-saving asset management of PROFINET networks with PROFINET and PROFIBUS field devices directly from the control room

Ethernet Access Point to PROFINET networks

Provides 2nd channel to access the field devices
Acts as a PROFINET supervisor
Is part of one PROFINET network
Integrated 2-port switch for use in line or ring network topologies

Key Component for Transition to State-of-the-Art Technology

Re-use of existing PROFINET networks without requiring modification
Access to acyclic data via FDI communication server (OPC UA)

Technical Data

smartLink HW-PN
Hardware	Processor	Altera Cyclone V SoC with dual-core ARM Cortex-A9
	Status LEDs (Gateway)	PWR, RUN, ERR, BUS
	Real-Time Clock	Real-Time clock with buffering, setting the time via browser or by NTP server (buffer time depends on conditions such as ambient temperature and duration of use)
Interfaces	Ethernet	1 x IEEE802.3 10BASE-T/100BASE-TX/1000BASE-T, Connector: RJ45
	PROFINET	2 x IEEE802.3 10BASE-T/100BASE-TX, Connector: RJ45; Embedded PROFINET 2-port switch for line or ring topology Protocol: PROFINET RT / IRT, Support of PROFINET redundancy protocols
Supported	Communication Protocols	PROFINET, PROFIBUS
	PROFINET/PROFIBUS Proxies	Softing: pnGate DP, pnGate PA aplSwitch Field PA
Physical Properties	Dimensions (H x W x D)	120 mm x 28 mm x 110 mm
	Weight	Approx. 430g
	Power Supply	18 VDC … 32 VDC; SELV/PELV power supply mandatory Typical input current: 200 mA, maximum input current: 1 A (allowing for in-rush current at switch-on)
	Typical Power Loss	5 W
	Operating Temperature	-40 °C … +65 °C (see detailed mounting description in user manual)
	Storage Temperature	-40 °C … +85 °C
	Relative Humidity	10 % … 95 %, non-condensing
	Cooling	Convection, no fan
	Mounting	DIN rail 35 mm
	Protection Class	IP20
Conformity / Standards	CE	Electromagnetic compatibility (EMC) and Restriction of Hazardous Substances (RoHS) EN 61000-6-2 Generic standards – Immunity standard for industrial environments EN 61000-6-4 Generic standards – Emission standard for industrial environments EN 55032 Electromagnetic compatibility of multimedia equipment – Emission Requirements Class A EN 55011 Industrial, scientific and medical equipment – Radio-frequency disturbance characteristics – Limits and methods of measurement Class A EN 50581:2012/EN IEC 63000:2018 RoHS, Assessment to the restriction of hazardous substances
	FCC	FCC 47 CFR Part 15B Section 15.109 (Class A)
	VCCI	VCCI Voluntary Control Council for Interferences by Information Technology Equipment, April 2015

References

Scope of Delivery
Hardware	smartLink HW-PN
Documentation	User Guide as PDF download

Order Numbers
GEA-YA-026010	smartLink HW-PN
LRA-AA-027003	smartPlus PN, License access to one field device

Video

The post SmartLink HW PN first appeared on ATEVA Technologies.

EdgeGate Connector Gateway

Webmaster — Thu, 20 Feb 2025 17:26:24 +0000

EdgeGate Connector – Industry 4.0 Multiprotocol Gateway

EdgeGAte Gateway : OPC UA Server & MQTT Publisher Gateway for PLC Controllers and CNC Machines

edgeGate makes data integration easier than ever before. The gateway supports the connection to PLC & CNC Controllers and uses the OPC UA standard for a simple and secure data integration into higher-level management systems, such as ERP, MES, or SCADA for new and existing plants.

In addition, edgeGate also offers MQTT Publisher/Subscriber functionality, enabling direct integration of machine data into private or public IoT cloud applications on the IT side. The generic MQTT implementation supports the use of many different cloud providers. Like the OPC UA standard, MQTT also supports various security mechanisms such as encrypted connections, certificates, and user authentication, thus contributing to a high level of data security.

To optimize security and performance in task-oriented environments, the edgeGate device comes equipped with three key applications: general device management, license management, and a communication interface. With this functionality, edgeGate is a compact, secure, future-oriented, and proven gateway for data integration.

Overview

Access to existing PLC and CNC controller data

Supports up to 20 connections for access to Simatic Siemens PLC, Allen-Bradley PLC, Siemens Sinumerik controllers, Fanuc CNC controller, Modbus TCP controller, or OPC UA machine data.
Easy local and global access to field data and routing through firewalls.
Protect investment through simple retrofit upgrades, as well as for modern controllers’ integration, without require modifying the running configuration in them.
No PLC programming or dedicated PC required.

Standardize and simplify the machine data integration

Integration of higher-level management systems like ERP, MES, or SCADA using integrated OPC UA Server providing open, platform-independent, and market-proven communication.
Simple data transmission to an MQTT broker using the MQTT publisher functionality for local or cloud-based solutions.
Separate Web interface for gateway configuration and data access application to avoid misconfigurations.

Industry-proven security

Physically separated interfaces for OT and IT networks add security layer to the plant.
Supporting security standards such as SSL/TLS and X.509 certificates.
Support of all security functions of OPC UA and MQTT.
Filtered access depending on IP address (Whitelist / Blacklist for OPC UA endpoints).

Technical Data

Hardware	Processor	Broadcom BCM2711 quad-core ARM Cortex-A72 (ARM v8) 64-bit SoC @ 1,5GHz
	Status LEDs (Gateway)	PWR (Power Supply), RUN (Running), ERR (Error), APP (Application)
	Real-Time Clock	Real-Time clock with buffering, setting the time via browser or by NTP server (buffer time depends on conditions such as ambient temperature and duration of use)
Interfaces	Ethernet	2x IEEE 802.3 10BASE-T/100BASE-TX/1000BASE-T, Connector: RJ45
	USB	1x USB 2.0, Connector: Type A
	HDMI	1x HDMI 2.0, Connector: Type A
Supported Communication Protocols	Northbound	MQTT V3.1, V3.1.1, & V5 OPC UA Server
	Southbound	OPC UA Client Modbus TCP SIMATIC S7, RFC1006, S7+: S7-300, S7-400, S7-1200, S7-1500 PLCs EtherNet/IP CIP: Allen-Bradley ControlLogix (CLX) and CompactLogix PLCs Sinumerik (RFC1006): Sinumerik 840D PL & SL CNCs FOCAS (Ethernet): FANUC CNCs Series 30i, 31i, 31i-B, 31i-B5, 32i-B, 35i-B, 0i-D, 0i-F, 0i-F Plus, Power Motion i- A, and FANUC NCGuide (Simulator)
Physical Properties	Dimensions (H x W x D)	120 mm x 28 mm x 110 mm
	Weight	Approx. 420g
	Power Supply	24Vdc ±20%, SELV/PELV supply mandatory, typical input current 500mA (max. 1A, considering rush-in current at switch-on)
	Typical Power Loss	9.5W
	Operating Temperature	-20°C … +60°C
	Storage Temperature	-40°C … +85°C
	Relative Humidity	5% … 95%, non-condensing
	Cooling	Convection, no fan
	Mounting	DIN rail 35mm
	Protection Class	IP20
Conformity/Standards	CE	Electromagnetic compatibility (EMC) and Restriction of Hazardous Substances (RoHS) EN61000-6-2 Generic standards – Immunity standard for industrial environments EN61000-6-3 Generic standards – Emission standard for residential, commercial, and light-industrial environments EN61000-6-4 Generic standards – Emission standard for industrial environments EN61326-1 Electrical equipment for measurement, control, and laboratory use EN61131-2 Programmable controllers – zone B EN55011 Industrial, scientific, and medical equipment – Radio-frequency disturbance characteristics – Group 1 Class B EN55032 Electromagnetic compatibility of multimedia equipment – Emission Requirements – Class B EN 50581:2012/EN IEC 63000:2018 RoHS, Assessment to the restriction of hazardous substances
	FCC	FCC 47 CFR Part 15B and ICES-003 – Class B
	VCCI	Class B Information Technology Equipment (ITE) set forth in the Agreement of Voluntary Control Council for Interference by Information Technology Equipment (VCCI), April 2015

Downloads

Documents

Datasheet: EdgeGate Connector

Technical specifications and features.

Download

EdgeGate Connector — Cloud Access

Access to user manual and documentation via our secure cloud.

Drivers & Software

Software and configuration tools.

Request Download

Documentation

User manual and technical documentation.

Request Download

Other

Additional resources.

Request Download

References

GAA-YY-051000	edgeGate
LRL-XX-161001	edgeConnection – Perpetual License*
^{* edgeConnection License already include 1 Year Software Upgrade license (LMA-XX-161001)}

Training

Misc

Video

The post EdgeGate Connector Gateway first appeared on ATEVA Technologies.

edgeConnector 840D

Webmaster — Tue, 28 May 2024 17:23:22 +0000

Edgeconnector 840D Software module for connecting SINUMERIK 840D controllers to industrial IoT applications

Container technology with access to SINUMERIK 840D Solution Line and Power Line data via OPC UA and MQTT with flexible deployment options for higher-level applications

edgeConnector 840D connects to the Siemens SINUMERIK 840D Solution Line and Power Line controllers without any intervention in the machine configuration and provides the data as an OPC UA server. In addition, the data can also be transmitted to MQTT brokers using MQTT. All process parameters from the NC part (axis, tool, program data), as well as the PLC part (status, program sections, alarms) and the drive data can be read out. As a Docker container, the product offers flexible deployment options, e.g. on standard IPCs or devices running Azure IoT Edge or AWS IoT Greengrass.

The application can be easily configured locally via an integrated web interface. It can also be managed remotely using the REST API. The configuration is flexible and includes precisely coordinated security settings (e.g. role-based access rights for OPC UA client applications).

The new product, which is also based on virtualization and container technology, benefits from Softing’s deep experience with brownfield connectivity through MQTT and OPC UA technology and provides the data for new and highly efficient IoT solution architectures.

Overview

Accessing Tooling Machine Data from OPC UA Applications

Provision of SINUMERIK 840D Solution Line and Power Line data
Pre-defined namespace, customizable for special machine data sets
Automatic tool recognition and listing of all available magazines and tools
Standardized OPC UA communication for data integration into management systems like ERP, MES, or SCADA or for data exchange with other docker containers like Microsoft OPC Publisher or Amazon AWS IoT SiteWise
Connection of up to 20 SINUMERIK 840D controllers with one Container Runtime
Reading of NC/PLC alarms, as well as GUD variables and R parameters
Dedicated for retrofit upgrades of existing SINUMERIK controllers

Easy Cloud-driven or Local Deployment

Container images stored in different online repositories like Docker Hub, Azure Container Registry (ACR) or Amazon Elastic Con-tainer Registry (ECR)
Simple data transmission to an MQTT broker using the MQTT publisher functionality for local or cloud-based solutions
Recipe manager functionality for writing process data from the cloud to controllers (MQTT Subscriber)
Licensing via Softing Floating License Server

Lightweight Flexible Container Solution

Less resources plus increased scalability and flexibility
Support of security standards as SSL/TLS, X.509 certificates, authentication, and data encryption
Highly flexible state-of-the-art application to be deployed, adjusted, or started and stopped immediately, if needed
Deployment and configuration also via management systems such as Kubernetes, Azure IoT Edge or AWS IoT Greengrass

Technical Data

edgeConnector 840D
Supported Controllers	Siemens SINUMERIK 840D Solution Line, software version V2.7 and higher Siemens SINUMERIK 840D Power Line, software version V5.3 and higher
Supported Protocols	OPC UA, MQTT SIMATIC S7 (RFC1006), SINUMERIK (RFC1006
Supported MQTT Specifications	V3.1, V3.1.1 & V5
Supported MQTT Features	MQTT Publisher & Subscriber TCP, TLS/SSL, WS, WSS, (including certificates) QoS, Retain, Last Will & Testament Store & Forward
Supported OPC Specifications	OPC Unified Architecture V1.04
OPC UA Roles	OPC UA Server
OPC UA Profiles	Data Access
OPC UA Security	Security methods	Aes256Sha256-RsaPss Aes128SHA256-RsaOaep Basic256Sha256 Basic256 Basic128Rsa15 None
	Authentication	Anonymous Username and password Certificate
OPC Compliance	Test based on compliance test tools of OPC Foundation
Configuration Interface Authentication	Username / Password LDAP/LDAPS
Logging, Diagnostics	Built-in trace and audit logging facilities, configurable and accessible through the web interface Docker integrated trace logging Prometheus Metrics Information
Supported Operating Systems	Linux (Docker Engine), Windows 10 and Windows 11 (Docker Desktop), Windows Server 2019 and Windows Server 2022 (Docker Enterprise Edition)
Supported Architectures	AMD64, ARM64, ARM32
Supported Container Orchestration Systems	Kubernetes (K8s), Amazon ECS
Minimum Hardware Requirements	320 MB free disk space, 2 GB RAM
Licensing	Licensed via Softing Floating License Server
Demo Version	20 PLC connections timed at 72 hours
REST-API	Access using the edgeConfigurator, download via Docker Hub

Downloads

edgeConnector 840D — Cloud Access

Access to all downloads from our cloud: License Manager, symbol files, Docker images and documentation.

Drivers & Software

Softing License Manager, edgeConnector 840D (DockerHub / Azure Marketplace).

Request Download

Documentation

Preconfigured symbol files for SINUMERIK 840D, dataFEED Exporter.

Request Download

Other

Checksums and additional resources.

Request Download

References

Scope of Delivery
Software	dataFEED edgeConnector 840D, download via Docker Hub or Azure Marketplace
License Key	E-mail delivery
Documentation	Online help (German / English) and online: www.github.com/SoftingIndustrial/datafeed-edge-connector

Order Numbers
LRL-XX-161001	edgeConnection – Perpetual License*
LMA-XX-161001	edgeConnection – Software Upgrade License
^{* edgeConnection License already include 1 Year Software Upgrade license (LMA-XX-161001)}

Additional Products and Services
	edgeAggregator
GPA-CS-041000	NETLink S7-Compact (for S7-300/S7-400 without CP or Ethernet connection)
6FC5851-1XC45-4YA8	SINUMERIK 840D sl CNC software and SINUMERIK Operate, toolbox including NCVar Selector (please order directly from Siemens)

Misc

Video

Getting started with CNC Machine Data

Wiki

Softing dataFEED edgeConnector 840D is a containerized SINUMERIK 840D SolutionLine and PowerLine connectivity module adding OPC UA Server and MQTT Publisher functionality. The software can run as IoT Edge Module. After the deployment, it is possible to configure Southbound and Northbound communication via local GUI or REST interface.

For southbound communication it is possible to connect up to 20 SINUMERIK 840D SolutionLine and PowerLine controllers. The Namespace configuration is pre-configured and can be extended via STEP7/TIA Portal or .awl files.

The northbound communication runs with standardized OPC UA communication for data integration into management systems like ERP, MES or SCADA or for data exchange with other docker containers like Microsoft OPC Publisher for cloud scenarios. In addition MQTT is available as protocol to connect MQTT Broker in local or cloud environments.

The application supports security standards like SSL/TLS, X.509 certificates, authentication and data encryption. The container runs for 72h in demo mode. Fully activate the application via BYOL from Softing. This also requires the installation of the Softing floating license server available for Windows/Linux.

After the Docker image has been pulled, a Docker container can be started. The webserver and OPC UA Server of the module have to be exposed on the host machine if dataFEED edgeConnector 840D shall be accessed from outside the dockerized environment.

To start dataFEED edgeConnector 840D with the default ports mapped 1:1 to the host machine:

docker container run -p 443:443 -p 4897:4897 softingindustrial/edgeconnector-840d

Softing licenseServer

Softing licenseServer is used to host network software licenses (also called floating licenses or shared licenses) that are installed locally on an individual users’ machine. The network licenses can be shared among many users and/or applications.

Softing licenseServer fulfills requests to run a network application if the required license is available. When the network license is released (for example, a user closes the application), the license is moved to the license server’s available license pool and is made available for other checkout requests.

The license server is used by several Softing products like the edgeConnector or plantPerfect product families.

Please read the user guide of the licenseServer for install and usage instructions. It is available as download on the Softing product pages using the licenseServer.

Installation

Download the docker image using the following command:

docker pull softingindustrial/license-server

Use the following commands to create and configure Docker container:

mkdir -p /var/lib/license-server
mkdir -p /var/lib/license-server/licenses
mkdir -p /var/lib/license-server/config
mkdir -p /var/lib/license-server/users
docker create --name license-server -p 8000:8000 -p 6200:6200 -v /var/lib/licenseserver/licenses:/root/.x-formation -v /var/lib/license-server/users:/root/sflm/users -v /var/lib/license-server/config:/root/sflm/config --restart=always softingindustrial/license-server
docker start license-server

The following ports are used by the license server:

Port	Service
6200	Network License Server
8000	HTTPS Web Server

These ports are mapped in the docker create call above 1:1 to the ports of the host system. Of course, you can map them to different ports on the host system by changing the first number on the -p option (example: -p 8400:8000).

To disable HTTPS, use the docker create command without a port mapping for port 8000.

Note: You will need access to the Web server to add licenses.

These following volumes are used by the license server:

Volume	Description
/root/.x-formation	Folder to store the license files
/root/sflm/users	Folder to store the user data
/root/sflm/config	Folder to store the configuration of the license server

The directory /var/lib/license-server is used to persist the configuration of the license server container. Of course, you can store it in a different folder on the host system by changing the first folder on the -v option (example: -v /home/xxx/ls:/root/.x-formation).

The option –restart=always will start the container on the startup of the system or restart it on failure.

Start the container with the following command:

docker start license-server

Stop the container with the following command:

docker stop license-server

Remove the container with the following command:

docker rm -f license-server

====================================

You might also be interested in ….

The post edgeConnector 840D first appeared on ATEVA Technologies.

FG-200 Gateway

Webmaster — Fri, 01 Mar 2024 09:59:58 +0000

Fieldbus Foundation Gateway : FG-200

Fieldbus Foundation Gateway :

FG-200The FG-200 HSE ( High Speed Ethernet ) /FF ( Foundation fieldbus ) Modbus Gateway : for the integration of control system on Modbus TCP

Overview

Quick and easy commissioning of the Softing gateway: FG-200FF

Optional support for the STHAL Carrier 9419 Bus and Fieldbus 9412 Power Supply (wiring reduced to a minimum)
Import Modbus data to a web server reducing mapping efforts

Optimized Management: Softing: FG-200FF

“Visitor” mode to avoid any interference with the network
Possibility of system management using different software (e.g. Emerson’s AMS) and Field Device Tool (FDT) frame applications (e.g. SMART VISION, FieldMate, Field Device Manager, FieldCare, or PACTware)
Redundancy capacity for Softing Gateway: FG-200FF

Possible redundancy link (D-3 according to FF-593)
Automatic mirroring with data configuration
Very fast redundancy

All necessary tools included

“FF Configuration Tool” for configuring devices and cyclical communication
PACTware for device configuration and basic management.

Technical Data

Downloads

Documents

Datasheet: FG-200 HSE/FF Modbus Gateway

Technical specifications and features of the FG-200 HSE/FF Modbus Gateway.

Download

ATEX Certificate of Conformity

Hazardous location certification documentation.

Download

Achilles Test Report

FG-200 HSE/FF cybersecurity robustness test report.

Download

FG-200 Gateway — Cloud Access

Access to software, firmware, drivers and documentation via our secure cloud.

Drivers & Software

FF HSE DTMs V1.50, Firmware FG-200FF, Search & Configure utility and additional drivers.

Request Download

Documentation

Communication Configuration Tool V2.24, user manual and technical documentation.

Request Download

Other

Whitepaper on Foundation Fieldbus gateway integration and additional resources.

Request Download

References

Description

Hardware	FG-200 HSE/FF Modbus
Logiciel	Outil de configuration FF, FDT CommDTM, PACTware sur CD-ROM
Documentation	Quick Startup Guide, User Manual sur CD-ROM

Références

GCL-EK-024100	FG-200 HSE/FF Modbus (Foundation fieldbus / Modbus TCP )
GCL-EK-024101	FG-200 HSE/FF Modbus, functionalité, conception identique pour une utilisation avec R. STAHL bus-Carrier Series 9419 et Alimentation Fieldbus série 9412

Training

Misc

Modbus HSE <> Fieldbus Foundation Gateway, 4 segments FF

HS Code 85176200

Video

All our videos on the FG-200 available on our cloud

ATEVA Videos

The post FG-200 Gateway first appeared on ATEVA Technologies.

mbGatePB

Webmaster — Sat, 29 Jul 2023 12:16:25 +0000

MODBUS TCP SERVER to PROFIBUS PB (PA/DP) Master Gateway

Simple connection of PROFIBUS Slave Devices to Modbus Control Systems via Internal I/O Mapping

With mbGate PB it is possible to integrate up to 2 PROFIBUS PA segments and 1 PROFIBUS DP segment into Modbus TCP control systems. It acts as Modbus TCP Server and PROFIBUS Master. With our gateway the engineering costs can be reduced since it re-uses existing power conditioners in technology upgrade projects. It enables configuration, parameterization and plant asset management using standard industry tools.

Overview

mbGate PB Gateway : Key Component for Transition to State-of-the-Art Technology

Simple replacement of installed PROFIBUS DP/PA segment couplers
Re-use of existing PROFIBUS segments without requiring modification

Direct Connectivity to PROFIBUS Segments

Single access point to PROFIBUS DP and PROFIBUS PA segments from Modbus TCP networks
Acting as Modbus TCP Server and PROFIBUS PA and PROFIBUS DP Master
Support of one PROFIBUS DP segment and up to two PROFIBUS PA segments
Support of up to 64 PROFIBUS devices

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

Supports major Modbus engineering tools such as Schneider Unity Pro or Siemens TIA Portal
Included CommDTM allowing use in FDT/DTM frame applications
EDD-based device parametrization using Siemens Simatic PDM

MODBUS/TCP Redundancy

Supports the use of two redundant PLCs and two redundant gateways
Easily enabled via licensing
Full control of redundant operation mode via engineering and PLC

Downloads

Documents

Datasheet: mbGate PB

Technical specifications and features.

Download

mbGate PB — Cloud Access

Access to firmware, drivers and documentation via our secure cloud.

Drivers & Software

Firmware, PROFIdtm, Search and Configure tool, PDM Libraries, PACTware.

Request Download

Documentation

Modbus Gateways User Guide, samples.

Request Download

Other

Additional resources.

Request Download

Reference

Scope of Delivery
Hardware	mbGate PB Gateway
Documentation	On Website

Order Numbers
GCA-EN-024808	mbGate PB, Modbus TCP to PROFIBUS Gateway. Supports 2 PA segments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).

Additional Products and Services
LRA-EN-024851	gatePlus HighAvailability, License for activating redundancy features in mbGate PB
LRL-DY-134501	dataFEED OPC Suite, Version 4.01 and higher, including all supported PLC protocols, support for OPC UA, access for any number of dataFEED OPC Tunnel Clients, for simultaneous access to a total of up to 100 OPC UA Servers, OPC Servers and OPC Tunnel Servers, and many more Functionalities such as Database and File Access, Data Exchange, Optimizer, Concentrator and Bridge
GCA-EL-024802	mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 2 PA segments (up to 32 PA devices).
GCA-EL-024804	mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 4 PA segments (up to 64 PA devices).
GCA-EN-024806	mbGate DP, Modbus TCP to PROFIBUS DP Gateway. Supports 1 PROFIBUS DP segment (RS485).

Vidéo

Video Channel : Retrouvez nous sur notre page channel YOUTUBE

The post mbGatePB first appeared on ATEVA Technologies.

pnGate DP

Webmaster — Mon, 27 Jun 2022 17:20:30 +0000

pnGate DP : PROFINET Gateway for PROFIBUS Slave

The pnGate DP allows you to connect PROFIBUS slaves to a PROFINET network. Keep your PROFIBUS slaves reliable and important. no more endless lengths of Profibus cable, which cause reflection problems. the gateway, as soon as possible, will solve the problem.

Overview

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

Supports major PROFINET engineering tools such as TIA Portal, Step7 und PC WORXS
Included CommDTM allowing use in FDT/DTM frame applications
EDD-based device parametrization using Siemens Simatic PDM

Direct Connectivity to PROFIBUS Segments

Single access point to PROFIBUS DP segment from PROFINET networks
Acting as PROFINET device and PROFIBUS DP master
Support of one PROFIBUS DP segment
Support of up to 32 PROFIBUS devices

Key Component for Transition to State-of-the-Art Technology

Re-use of existing PROFIBUS segments without requiring modification
Support of MRP and S2 PROFINET redundancy for increased reliability

Downloads

Documents

Datasheet: pnGate DP

Technical specifications and features.

Download

pnGate DP — Cloud Access

Access to software, firmware, drivers and documentation via our secure cloud.

Drivers & Software

Profibus API and Drivers, Search and Configure tool, firmware.

Request Download

Documentation

User guide and technical documentation.

Request Download

Other

Additional resources.

Request Download

Reference


GCA-AN-024606	pnGate DP, PROFINET to PROFIBUS DP Gateway. Supports 1 PROFIBUS DP segment (RS485).

Additional Products and Services
LRL-DY-134501	dataFEED OPC Suite, Version 4.01 and higher, including all supported PLC protocols, support for OPC UA, access for any number of dataFEED OPC Tunnel Clients, for simultaneous access to a total of up to 100 OPC UA Servers, OPC Servers and OPC Tunnel Servers, and many more Functionalities such as Database and File Access, Data Exchange, Optimizer, Concentrator and Bridge
GCA-AN-024608	pnGate PB, PROFINET to PROFIBUS gateway. Supports 2 PA segments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).
GCA-AL-024602	pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 2 PROFIBUS PA segments (up to 32 PROFIBUS PA devices).
GCA-AL-024604	pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PROFIBUS PA devices).

Vidéos

The post pnGate DP first appeared on ATEVA Technologies.

Serveur TCP/IP-H1 for Sinec H1 communication

Webmaster — Wed, 04 Aug 2021 14:58:00 +0000

TCP/IP-H1-OPC-Server

All-in-one OPC Server With Maximum Protocol Scope Via TCP/IP and H1 (Included in Former INAT Multi-Protocol OPC Server)

The TCP/IP-H1 OPC Server offers uniform access to the leading controllers of the companies Siemens, Rockwell Automation, Schneider Electric or Mitsubishi. This high-performance OPC Server is easy to configure and offers a wide variety of diagnostic capabilities.

general

Everything at a Glance

Functionality based on customer requirements
Ethernet protocol dependent on controllers and field devices
Reliable communication with control system

Application Area

Heterogeneous networks with controllers and devices from a wide variety of different manufacturers
Support of standard TCP/IP, Sinec H1, various serial protocols
Increased investment protection for integration of existing systems

Features

High-performance protocol for transmission of large amounts of data via OPC
No limit to number of connected controllers and variables
High degree of reliability for all OPC Clients with OPC interface V1.x and V2.05
Easy to commission via symbolic addressing (Alias Browsing)
Easy symbol import directly from STEP 7 project
Increased availability due to continuous line monitoring and extensive communication diagnostics
SNMP access to devices of different vendors via MIB Import and SNMP Browse

détails technique

Supported Controllers	Softing and Siemens CPs, Allen Bradley CLX, SLC and PLC 5 controllers, Mitsubishi Melsec-Q vontrollers, various Modbus TCP interfaces, SNMP devices
Supported Protocols	See table
Supported Operating Systems	Windows XP, Windows 7, Windows 8, Windows 8.1, Windows 10, Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Demo Version	Full TCP/IP-H1 OPC Server functionality, time-limited to 72 hours

téléchargements

Downloads

Drivers & Software
- OPC Server-TCP / IP-H1 V5.00 demo version (72 hours runtime) and full version for license holders version 5.00
- OPC License Manager V4
Manuals & Documentation
- OPC Server Manual E-032012-01
- OPC Competence Brochure
Data Sheets
- TCP/IP-H1 OPC Server Data Sheet

Références

ATV-LRL-DY-131001	TCP/IP-H1 OPC Server, single license
ATV-UAC-DD-0100	USB hardware for replacing the software key required for activating a Softing product

Additional Products and Services

ATV-GPL-CS-191000

echolink S7-compact

Scope of Delivery

Software	TCP/IP-H1 OPC Server on CD-ROM
Documentation	Online Help in English and German

The post Serveur TCP/IP-H1 for Sinec H1 communication first appeared on ATEVA Technologies.

Certificator : NetXpert XG2

Webmaster — Tue, 03 Aug 2021 17:09:02 +0000

NetXpert XG2 : Test, verify and certify your Ethernet Network . let Garanty the speed on your cable.

NetXpert: the ultimate solution

The speeds of “Wireless Access points” often exceed the speeds of cabling installed in the network. Is it possible that your cables handle speeds well beyond their specifications? Is it possible that your CAT5e or CAT6 cables can reach speeds of 1GBits/S or even 10Gbits/s?

To find out, a simple function on the NetXpert XG2 allows you to perform 3 tests. Performs a speed test by sending 1Gb/s of data via your cable (BERT Test) and it will prove if it will perform beyond specifications and follow the speed of the installed “Access Points”

The NetXpert is the only cable tester and active network manager to perform Bit Error Rate Test (BERT), Signal to Noise Test (SNR) and Speed Delay of 1Gb/s, 5Gb/ s or 10Gb/s at the touch of a button. You can now perform real-time throughput tests to validate your cables up to 10Gb/s.

Test error rate, noise and propagation delay instantly

By performing a bit error rate test (BERT) and according to IEE802.3an standards, the NetXpert XG certifies you or not, error-free data transmission up to 10Gb/s

One-touch self-test includes Signal-to-Noise Ratio (SNR) and Time Offset, which can have a significant impact on Gigabit transmission

The signal-to-noise ratio verifies that the noise is low enough and the signal is high enough for reliable transmission. “Propagation delay” indicates an offset between wire pairs. Excessive delay can cause serious degradation of transmission and therefore performance.

The 3 basic measurements to determine whether a transmission is reliable or not can be done with just one touch. Once the measurement is done, you can repeat it immediately using this unique function. Each measurement is archived and provided with a final summary report in PDF, CVS or XML format

Dépannage du réseau actif PoE++

Lors de dépannage de réseaux actifs PoE++ , le NetXpert XG offre une série de mesures exhaustives. Cela inclut le test de charge pour vérifier la perte de tension et assurer ainsi une stabilité de l’alimentation PoE, l’identification des appareils connectés au réseau et la détection de la disponibilité d’appareils prioritaires.
Le NetXpert XG offre un espace de stockage interne suffisant pour de gros projets et génère des rapports de test complets conformément aux normes en vigueur. Sa large gamme d’accessoires fait du NetXpert XG l’outil de qualification incontournable – de la localisation individuelle de câble et son générateur de tonalité intégré ou bien ses bouchons d’identifications en passant par la génération de rapports de mesure et le dépannage de réseaux PoE++.

Général

The cable qualifier that is defining a new category — the cable project qualifier

If you are a cable installer, network owner, network builder, or system integrator, you’ll be excited to hear that NetXpert XG includes a project editor and auto test generator for up to 1000 cables, and test reports you can keep for your records or leave with your customer. Once the tests are created, plug in the cable, click test, and NetXpert XG starts testing the cable to IEEE 802.3 standards to prove the speed of your cable. Not only do you get a wiremap and cable length, NetXpert XG tests BERT, SNR, Delay Skew, distance to opens, shorts, or miswires. As a bonus you get active network tests for copper, fiber, and wireless. And, with 2 NetXpert XG local units, you can test fiber cables.

Cable Project Qualifier

Use the project editor, cable test editor, test label editor to pre-configure your cable testing projects
Press test to automatically sequence up to 1000 cable tests from the local or remote device to increase cable testing efficiency when working alone
Test data cabling for IEEE 802.3 compliance at data rates up to 10 Gb/s (BERT)
Determine signal-to-noise ratio (SNR) for compliance up to 10 Gb/s
Measure delay skew for compliance up to 10Gb/s
Measure length of cable with TDR and capacitance measurements for highly accurate test results and easier troubleshooting
Full-color wire map shows distance to open, distance to short, miswires, split pairs, and shield on a color graphical display
Save test results and generate standards-based measurement reports providing “Pass/Fail” indication in pdf, csv, or xml format

Perform active network management

Support for IPv4 and IPv6
Discover your network and see the connected network devices
Identifies defective PoE switches with a PoE load test
DHCP test
Ping lists can be defined and saved for later use
LLDP/CDP detection and analysis
Identifies VLANs present in your network
Data transfer from the tester to the PC using USB stick, wireless, or bluetooth connectivity

Details Techniques

Length Measurement Technology	Time-Domain Reflectometry (TDR) and capacitance
Cable Measurements	Cable Testing and ID: up to 1,000 ft (305 m) Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m) Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft (30 cm)) Distance to fault: 0 to 656 ft (200 m) ± (5% + 3ft (1m)) Supports 8 wiremap remotes (RJ 45) and 24 RJ-45 ID only remotes
Power over Ethernet (PoE)	Test supports IEEE 802.3af PoE (Type 1, max 15.4W), IEEE 802.3at PoE+ (Type 2, 30W) and 802.3bt PoE++ (Type 3, 60W) Future proofed for IEEE 802.3bt Type 4 100W higherpower PoE
Active Ethernet	Network and test support by interface: Copper RJ-45 interface –100/1,000/2,500/5,000/10,000 Mb/sec link speeds Fiber SFP+ #1 interface supports 10Gb/sec link speed Fiber SFP+ #2 interface supports 1Gb/sec link speed WiFi 802.11 a/b/g/n 2.4 Ghz WiFi and Bluetooth
Maximum Voltages	Maximum voltage that can be applied to any 2 connector pins without causing damage to the tester: RJ-45: 60 VDC or 50 VAC
Save Test Results	Stores virtually unlimited cable or network tests with user defined names per project
Tone Generation	Tone Frequencies: 730 Hz and 1440 Hz
Languages	English, German, French, Spanish
Battery	Li-Ion, 7.2 VDC, 3.1A-hr (typical) Battery Life at 10Gb: 5 hrs minimum, 24 hrs stand-by
Temperature	Operating: 14 to 140° F (-10 to 60°C) Storage: -22 to 158°F (-30 to 70°)
Humidity	10 to 90% non-condensing
Enclosure	Injection molded plastic
Display	7″ Color TFT-LCD capacitive touch display, 1024 x 600 resolution (WSVGA)
Size	245 x 177 x 73 mm (main unit) 130 x 177 x 55 mm (Active Remote)
Weight with Battery	2.6lbs (1.2 kg) main unit 1.3lbs (0.6 kg) Active Remote

Téléchargement

Documents :

References

Comparaison


Features	NetXpert XG PLUS	NetXpert XG 10G	NetXpert XG 2.5/5G	NetXpert XG 1G
Active network test on Copper
Passive qualification test on Copper
Active network test on Fiber Optic (SM/MM)
Passive qualification test on Fiber Optic (SM/MM)
Maximum speed:	10Gbps	10Gbps	5Gbps	1Gbps

Mainframe unit:	2	1	1	1
Active remote unit:	1	1	1	1

Upgradeable to NetXpert XG – 2.5/5G
Upgradeable to NetXpert XG – 10G
Upgradeable to NetXpert XG – PLUS

Compatible with Fiber Microscope
Compatible with Cable Probe (CP15)
Compatible with ID remote identifiers

Compliant to IEEE 802.3an Standards to support up to 10Gbps
Compliant to 802.3af/at/bt to support PoE/+/++ testing
Compliant to Wi-Fi 802.11a/b/g/n/ac to support Wi-Fi.

Generate graphical PDF reports

The post Certificator : NetXpert XG2 first appeared on ATEVA Technologies.

PBPRo Ethernet ( PBPro-eth )

Webmaster — Tue, 23 Feb 2021 18:49:07 +0000

PBpro ETH

Remote PROFIBUS Interfaces for Use as Master or Slave

PBpro ETH is a family of interfaces for remote access to one, two, three or four PROFIBUS segments via Ethernet for device parameterization, controller programming and data acquisition. On the PC the remote interface acts like a local PROFIBUS board.

Overview

Wide Range of Applications

De-facto standard for device parameterization via FDT/DTM
PROFIBUS connection for PC-based measuring and monitoring systems
External PROFIBUS interface for PC-based field devices and embedded computer systems

Individual Protocol Settings for Each Channel

Access to process data and parameters in connected devices as PROFIBUS DP Master or Master Class 2 (also simultaneously with existing control systems)
Data exchange with controllers as PROFIBUS DP Slave
Integration into PROFIBUS FMS systems, or into proprietary applications via PROFIBUS FDL
Each channel acting as an individual PROFIBUS PC interface

Easy Administration and Efficient Integration

Assignment of IP address and configuration with accompanying “Search and Configure” tool and integrated web interface
Commented sample programs for easy use of the PROFIBUS application programming interface (API)
Free-of-charge communication DTM for PBpro ETH supporting parameterization of PROFIBUS devices by FDT tools

Technical details

	PBpro ETH Single Channel	PBpro ETH Dual Channel	PBpro ETH Triple Channel	PBpro ETH Quad Channel
Number of Channels	1	2	3	4
PROFIBUS Protocol
DP-V0 Master		All Channels	All Channels	All Channels
DP-V1 Master: Acyclic C2 Services		All Channels	All Channels	All Channels
FMS		All Channels	All Channels	All Channels
FDL		All Channels	All Channels	All Channels
DP-V0 Slave		Channel 2	Channel 2,3	Channel 2,3,4
Connector	9-pin D-Sub female, EIA-485 (RS-485), galvanically isolated
Transfer Rates	9.6; 19.2; 45.45; 93.75; 187.5; 500; 1500; 3000; 6000; 12000 Kbit/s
Host Interface
Ethernet	100BASE-TX/10BASE-T, 100 Mbit/s and 10 Mbit/s with automatic detection, RJ45 connector
Web Server	For device status and configuration
Remote API	Windows DLL for host computer
TCP/IP Socket Library	Easily portable source code and programming samples for non-Windows computers
Miscellaneous
Mounting	35 mm DIN Rail
Dimensions (W x H x D)	47 mm x 131 mm x 111 mm	110 mm x 131 mm x 111 mm	110 mm x 131 mm x 111 mm	110 mm x 131 mm x 111 mm
Power Supply	24 VDC (±20%) Typically 0.2A	24 VDC (±20%) Typically 0.3A	24 VDC (±20%) Typically 0.4A	24 VDC (±20%) Typically 0.5A
Temperature Range	0 °C … +55 °C (Operation); -20 °C … +70 °C (Storage); fanless convection cooling
Relative Humidity	< 90%, Non-Condensing
Protection Class	IP20
Available Drivers	Windows 2000, Windows XP, Windows Vista, Windows 7, Windows 8, Windows Server 2003 R2, Windows Server 2008

Downloads

Documents

Datasheet: PBPRo Ethernet

Technical specifications and features.

Download

PBPRo Ethernet — Cloud Access

Access to software, firmware and documentation via our secure cloud.

Drivers & Software

Software and firmware.

Request Download

Documentation

User manual and technical documentation.

Request Download

Other

Additional resources.

Request Download

References

DEL-NN-012311	PBpro ETH; 1 canal
DEL-NN-012312	PBpro ETH; 2 canaux
DEL-NN-012313	PBpro ETH; 3 canaux
DEL-NN-012314	PBpro ETH; 4 canaux

Scope of Delivery

Hardware	PROFIBUS Remote Interface
Software	Windows Drivers, Sample Programs, PROFIdtm
Documentation	User Guide

Produits complémentaires

OPC-PB	PROFIBUS OPC Server for DP-V0 / DP-V1
DCF-DY-4100	OPC Server for S7 / S5
TRA-PB-TECH	PROFIBUS Technology Training

PROFIBUS Tester PROFIBUS DP & PA
Login

The post PBPRo Ethernet ( PBPro-eth ) first appeared on ATEVA Technologies.

PROFIBUS Tester PROFIBUS DP & PA

Webmaster — Tue, 09 Feb 2021 15:41:41 +0000

The PROFIBUS Tester: ‘PROFIBUS Tester 5’ (pb-t5 or BC-700-PB) is a powerful diagnostic and troubleshooting tool for testing cables, measuring signals and analyzing communication of PROFIBUS networks. It is battery powered and provides a graphical display, which allows for quick results when working in standalone mode. Optionally, also the PROFIBUS PA network can be analyzed. Additionally, the BC-700-PB supports exporting test results for advanced analysis.

Overview

The PROFIBUS tester allows you to test cables, physical bus and “All-In-One” communication bus

Combination of signal tester, memory oscilloscope, protocolanalyzer, master simulator and cable tester functionality in one diagnostic tool
Standalone mode, plus extensive PC-based diagnostics
Suitable for installation, configuration and commissioning, documentation, acceptance testing, network optimization, preventative maintenance, troubleshooting as well as laboratory testing

Very mobile, the bus tester allows testing, even without a computer

battery operation without the need for additional power
Graphical display providing easy to understand presentation of test results
Complete network testing in standalone mode without requiring a laptop

Improved diagnostic features with PC-Based software add-on

Many additional features for running, analyzing and managing bus tests in PC mode (Trending, Topology Scan, Master Simulator, Oscilloscope, Frame analyzer)
Quick test and user-controlled test for easy network status assessment at the touch of a button
Generation of test reports which describe the current status of the PROFIBUS installation
Ideal for less experienced users, as well as fieldbus specialists

Optional measurement adapter for MBP (Manchester Coded Bus Powered) Physical

Specific analysis of MBP physical media signal (feedingvoltage, signal type, signal polarity, bitrate divergence)
Complete protocol analysis directly at the PROFIBUS PA segment level

Technical details

Diagnostics Functionality
Protocol and Frame Analysis	PROFIBUS DP-V0 and DP-V1, automatic baud rate detection in the range of 9.6 kbit/s … 12 Mbit/s
Signal Analysis	PROFIBUS DP-V0, DP-V1, FMS and MPI
… via EIA-485	Signal quality index 0 … 5,000, determined from signal wave form as well as signal/noise ratio and rise time; signal sampling with 8/16 samples per bit
… via MBP (requires optional adapter)	Fieldbus feeding voltage: 0 V … 35 V at 0.1 V resolution, signal level: 100 mV … 1,200 mV at 10 mV resolution, signal polarity, bitrate divergence: ±1.2 % at 0.01 % resolution, signal sampling with 128 samples per bit
Oscilloscope Display (Not Available for MBP)	Test range: ±5 V at 10 mV resolution (differential), 0 V … 15 V at 15 mV resolution (A or B to DGND); sampling rate: up to 384 Msamples/s; sampled points: 2,400 (signal details), 8,192 (oscilloscope analysis)
Topology Scan (Not Available for MBP)	Active, maximum distance: 230 m, accuracy: ±2 m
Cable Test (Not Available for MBP)	Active, supported cable segment length: 5 m … 1,500 m, accuracy: 5 %
Operation	Via graphical colour display, four function keys and scrollwheel including central push-button or via PC/notebook
Internal Memory Capacity	3 user-definable network directories (segment and test location) for storing quick tests, trend logs and cable test results Trend logging: max. 99 hours
Trigger	IN: L = 0 V .. 0.8 V; H = 2.4 V .. 24 V; pulse > 10 μs, active high OUT: approximately 5 V, active low (connection to storage oscilloscope)
PC Operating Software	PROFIBUS Diagnostics Suite, see separate datasheet for details
Connectors
EIA-485 (PROFIBUS DP)	PROFIBUS D-sub connector, 9 pins, power supply for external bus termination
MBP (PROFIBUS PA)	Connector, 3 pins, for screw terminals at optinal measuring adapter, measuring cable set including 3 probes(adapter for MBP measurement is attached to D-sub connector)
USB	V 2.0, high speed 480 Mbit/s, galvanically isolated
Dimensions (H x W x D)	35 mm x 220 mm x 110 mm
Power Supply	Built-in three-cell lithium-ion battery supporting 11.1 VDC or external AC adapter 100 VAC … 240 VAC, 50/60Hz (galvanically isolated) The rechargeable battery has a runtime of up to 5 hours (runtime depends on the performed test functionality and rate of wear of the rechargeable battery) Battery is charged via external AC adapter
Operating/Storage Temperature	Operating temperature: 0 °C … 50 °C, storage temperature: -20 °C … 70 °C
Relative Humidity	Air humidity: 10 % … 90 % without condensation
Weight	Test tool, no cable: approximately 0.75 kg; complete carrying case: approximately 4.2 kg
Conformity	CE, FCC, VCCI

Downloads

Documents

Datasheet: BC-700-PB

Technical specifications and electrical characteristics of the BC-700-PB module.

Download

PG-Diagtool — Software Download (Cloud Access)

PROFIBUS diagnostic tool for BC-700-PB. Click below to request the download link via our secure cloud.

Request Download

Reference

ATV-DDA-NN-006014	PROFIBUS Tester 5 (BC-700-PB)
ATV-DDL-NN-006012	PROFIBUS Tester 5 (BC-700-PB) with Oscilloscope Option
ATV-LRA-NN-006011	Oscilloscope Option (Oscilloscope view in stand-alone mode)
ATV-DDL-NL-006010	PROFIBUS PA option for BC-700-PB (BC-700-PB serial number required for order placement)

Scope of Delivery

Hardware	PROFIBUS Tester 5 (BC-700-PB), power supply unit 100 VAC … 240 VAC, 50/60 Hz with connecting cables for Europe and USA, adaptor cables, carrying case Measuring adapter BC-700-H1, measuring cable set (for PROFIBUS PA option)
Software	PROFIBUS Diagnostics Suite (PC software for Windows on CD-ROM) BC-700-PB upgrade license (on CD-ROM, for PROFIBUS PA option)
Documentation	Device Manual, “Getting Started“ Manual

Additional Products and Services

ATV-ACA-NN-006031	EIA-485 D-Sub adapter cable for testing operational networks with reduced influence on segment operation
ATV-ACA-NN-006033 (view product)	Adapteur D-Sub vers M12, fourni avec un T et bus M12 de terminaison, pour PROFIBUS DP
ATV-PB-LSZ-CHB3 (view product)	Pince pour mesure des courants de fuite. Localise les problèmes électromagnétique ( EMC ) . 40 ..1000 Hz, MIN/MAX, Data Hold, Cable pour mesure, fourni avec son étui.
ATV-BC-PBMB-PB-S (view product)	D-Sub Service Interface with Active Bus Termination and 90° Angled Connector for PROFIBUS DP
ATV-BC-M12DP-PB (view product)	M12 Service Interface for PROFIBUS DP, Comprising M12 T-Piece, End Cap and M12 Connection Cable (1 m)

Training

PROFIBUS Dépannage avec examen pour Certified PROFIBUS Installer

Analyse SW

PROFIBUS Diagnostics Suite

Universal Software for All Diagnostic Tools of the bus check Family

PC software for performing, evaluating and managing tests of bus physics, bus communication and cabling in PROFIBUS networks. The application is extremely easy to use, with a quick test available at a click of the mouse.

One Software for All Diagnostic Products

Comprehensive analysis of PROFIBUS DP and PROFIBUS PA networks
Diagnostic functionality available depending on connected test tool
License-free use on any number of PCs – no activation required

Suitable for the Fieldbus Novice

Bus test initiated with a single mouse click
Clear, easy-to-read display of test results
Separate expert mode providing in-depth diagnostic features for network specialists

Functionality for All Diagnostic Tasks

Continuous display of current bus status in status bar
Overall bus health indicated by traffic light symbols for bus physics and bus communication
Detail views with additional diagnostic information, also for advanced analyses by experts
Testing of bus and connected devices via integrated master simulator without configuration or parameterization
Generation of test reports for acceptance testing of PROFIBUS installations

Misc

Technical Data

Operating Systems: PC Hardware*	RAM	500 MB for Windows XP 1 GB for Windows 7, Windows 8
	Processor	1 GHz for recording at baud rates up to 1.5 Mbit/s 2 GHz for recording at baud rates over 1.5 Mbit/s
	Screen Resolution	1024 x 768 pixels (XGA)
	USB Interface 2.0
Supported Operating Systems	Windows XP, Windows 7, Windows 8, Windows 10

* The above minimum requirements are only general guidelines. Requirements may vary depending on the PC/notebook used.

accessories

Fieldbus Shield Digital Leakage Current Clamp – Locating EMC Problems

Measures leakage currents, e.g. leakage and fault currents, and current pick-up of instruments without breaking the circuit. Measurements according to DIN VDE 0701/0702 and the German BetrSichV (BGV A3, VBG 4).

Reliably Detects Even Very Small Improper Shield Currents Resulting from EMC Problems.

Functionality

Leakage current measurement
Differential current measurement
Voltage and resistance measurement
Frequency range for AC current / voltage 40 Hz…1 kHz
Acoustical continuity test
MIN/MAX and relative value measurement
Manual selection of the measurement range
Integrated data hold
Additional analog bar graph display
Clamp opening 30 mm
Auto power off

Included in Package

Digital leakage current clamp, 2 batteries 1.5 V IEC LR6, carrying case, measuring cables (1 x red, 1 x black) and user manual.

Order Number

DDA-ZZ-004010

M12 Service Interface for PROFIBUS DP

Application example:

Interface for Providing an Access Point to Test PROFIBUS Networks With M12 Connectors

Provides an access point for testing PROFIBUS networks with M12 connectors.

Allows Testing the Bus During Operation

Application

The service interface is inserted between two bus stations. When not in use, the service output of the T piece is closed with an end cap. At baud rates of 1.5 Mbit/s or higher, use the supplied cable to ensure that the required minimum distance between bus stations is maintained.

Included in Package

T piece (protection class IP68) with end cap and a 1 m DP cable fitted with a male/female M12 connector on each end.

Order Number

ATV-ACA-NN-006034

M12 adaptor PROFIBUS Tester PB-T5

Application example:

Interface for Providing an Access Point to Test PROFIBUS Networks With M12 Connectors

M12 Adaptor for PB-T5

Allows Testing the Bus During Operation

Application

Included in Package

M12 Adaptor for PB-T5

Order Number

ATV-ACA-NN-006033

Videos

PB-T5 – Logiciel PB-DIAG TOOL

[evp_embed_video url="/ftp/softing/PB-T5/PROFIBUS Troubleshooting with PROFIBUS Tester 5.mp4" preload="auto" template="mediaelement"]

PB-T5 – Logiciel PB-DIAG TOOL

[evp_embed_video url="/ftp/softing/PB-T5/PB-T5_Network_Acceptance_EN.mp4" template="mediaelement"]

Interested in this product ? you may be interested in these ones

TH Link PROFIBUS ( pour la paramétrisation FDT/DTM )
Testeur PROFIBUS PA pour Zone ATEX
Pince pour la mesure des courants de Fuites :
Valise de protection IP67 : Etanche et robuste, une garantie pour la protection de votre matériel

The post PROFIBUS Tester PROFIBUS DP & PA first appeared on ATEVA Technologies.

SOFTING | ATEVA Technologies

SmartLink HW PN

SmartLink HW PN

PROFINET Gateway for Asset Management

Access PROFINET networks via FDI and OPC UA

Parameterization and Asset Management

Compatible with established communication standards

Parameterization and Asset Management

Inexpensive and low-risk Integration

Compatible with established communication standards

Parameterization and Asset Management

Ethernet Access Point to PROFINET networks

Key Component for Transition to State-of-the-Art Technology

EdgeGate Connector Gateway

EdgeGate Connector – Industry 4.0 Multiprotocol Gateway

EdgeGAte Gateway : OPC UA Server & MQTT Publisher Gateway for PLC Controllers and CNC Machines

Access to existing PLC and CNC controller data

Standardize and simplify the machine data integration

Industry-proven security

Documents

Datasheet: EdgeGate Connector

EdgeGate Connector — Cloud Access

Drivers & Software

Documentation

Other

edgeConnector 840D

Edgeconnector 840D Software module for connecting SINUMERIK 840D controllers to industrial IoT applications

Container technology with access to SINUMERIK 840D Solution Line and Power Line data via OPC UA and MQTT with flexible deployment options for higher-level applications

Accessing Tooling Machine Data from OPC UA Applications

Easy Cloud-driven or Local Deployment

Lightweight Flexible Container Solution

edgeConnector 840D — Cloud Access

Drivers & Software

Documentation

Other

Softing licenseServer

Installation

edgeConnector 840D

NETLink Pro Compact

FG-200 Gateway

Fieldbus Foundation Gateway : FG-200

Fieldbus Foundation Gateway :

FG-200The FG-200 HSE ( High Speed Ethernet ) /FF ( Foundation fieldbus ) Modbus Gateway : for the integration of control system on Modbus TCP

Quick and easy commissioning of the Softing gateway: FG-200FF

Optimized Management: Softing: FG-200FF

All necessary tools included

Documents

Datasheet: FG-200 HSE/FF Modbus Gateway

ATEX Certificate of Conformity

Achilles Test Report

FG-200 Gateway — Cloud Access

Drivers & Software

Documentation

Other

Description

Références

mbGatePB

MODBUS TCP SERVER to PROFIBUS PB (PA/DP) Master Gateway

mbGate PB Gateway : Key Component for Transition to State-of-the-Art Technology

Direct Connectivity to PROFIBUS Segments

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

MODBUS/TCP Redundancy

Documents

Datasheet: mbGate PB

mbGate PB — Cloud Access

Drivers & Software

Documentation

Other

pnGate DP

pnGate DP : PROFINET Gateway for PROFIBUS Slave

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

Direct Connectivity to PROFIBUS Segments

Key Component for Transition to State-of-the-Art Technology

Documents

Datasheet: pnGate DP

pnGate DP — Cloud Access

Drivers & Software

Documentation

Other

Serveur TCP/IP-H1 for Sinec H1 communication